Affordable Filament Dryer: Keep Your 3D Prints Moisture-Free with Our Cheap Solution
Our filament dryer is a cheap, easy to use and reliable way to keep your 3D prints moisture-free.
If you're new to 3D printing or just want an easy way to make sure your prints are good quality, then this guide will show you how to use our cheap filament dryer solution with your printer. While it's possible that your design is flawed or your printer needs some tweaking, it's more likely that your filament isn't dry enough. This is a common problem for new users, but it's easy to solve. You just need a cheap filament dryer.
A filament dryer is a simple device that uses heat to dry out moisture from your filament before it enters your printer. This helps prevent warping and curling during printing and makes the finished product more durable and easier to handle after printing.
Have you ever tried printing a 3D model, only to find that the filament has become clogged?
If so, you're not alone. This is a common problem with 3D printers.
How to Keep Your Prints Moisture-Free
Moisture can cause your prints to warp and curl up before they even have a chance to dry. It’s a nightmare for 3D printing enthusiasts and professionals alike. With so many different types of filament, however, it’s difficult to know which ones will be affected by moisture and which ones are safe to use without extra precautions.
Fortunately, there is a simple solution: one that uses an inexpensive filament dryer.
This device will keep your filament dry and free of moisture, which will keep your prints from warping or curling up on themselves during the printing process.
3D printing is a great way to make your own unique objects and products. But if you don’t have a filament dryer, you may end up with a warped, cracked print that’s not worth your time or money.
But what if you don’t have the money to buy an expensive filament dryer? Here are some cheap ways to keep your prints moisture-free.
We'll talk about how to dry out filament, and help you find an affordable filament dryer for your home or office.
If you're new to 3D printing, you might not know that it's important to keep your filament dryer on hand. The best way to do this is with our affordable filament dryer solution.
The problem with 3D printing is that if you don't have a heated print bed, the bottom layer of your print can come out with a bit of a soggy bottom. This is because the moisture from your filament has not had time to evaporate before it gets printed. The result is usually a print with some very ugly ridges where the solidified plastic meets the un-solidified material underneath.
To combat this issue, you can use an affordable filament dryer to dry your filament before it goes into your printer. This will ensure that there is no excess moisture left in your filament which could potentially cause problems during printing.
What kind of problems? Well, if there's too much water in your filament then it might cause more warping than usual or even cause some parts of the print to fail completely (especially if they're large).
There are a lot of ways to make a filament dryer, but I wanted to create one that was cheap, easy to use and could be used with any printer.
Simple Methods for Drying Out Filament
The easiest method for drying out damp filament is just leaving it in an airtight container for a few days. The air will naturally evaporate any moisture inside the filament, allowing it to become usable again. This method isn't ideal because it may take longer than you expect, so you'll want to keep an eye on your filament container every day or two until it's ready to use again.
Another simple method is placing your filament in front of a fan or blowing hot air over it with a hair dryer (or other heat source). This will help dry out any excess moisture in your spool quickly, but it isn't very reliable because some parts of your spool won't receive enough airflow, leading them to remain too wet for long periods of time.
If you want to speed up the drying process even more, try placing your storage container in a microwave or oven (with the door open). The heat will help evaporate any residual moisture that might be present in your filament. Be careful not to overheat your filament; doing so could cause it to soften again and ruin your prints!
The last way to dry out filament is by using a dehydrator. Dehydrators are available at most grocery stores and supermarkets. They usually cost less than $50 and have multiple trays so that you can dry different types of materials at the same time. You can also use your oven if you don't have access to a dehydrator, but this method takes longer because you'll have to leave your filament in there for several hours (or even overnight) before removing it from the oven.